Materials data
Thermal-runaway barrier materials compared
Fibre-reinforced silica aerogel gives the lowest thermal conductivity of the common barrier materials. Mica resists flame, particle jets and high voltage best but insulates poorly. Ceramic-fibre paper sits between the two. Most production cell-to-cell barriers are now laminates that combine these properties.
Every value carries a status. Verified means it was read in the cited datasheet, with page and test condition recorded. Typical means a range compiled from several documents and not yet traced line by line. Use the supplier's current datasheet for design.
Summary of typical properties
| Material | k at ~25 °C, W/(m·K) | k at elevated temperature | Temperature limit | Density | Typical thickness | Compression | Electrical insulation |
|---|---|---|---|---|---|---|---|
| Silica aerogel blanket / pad (fibre-reinforced) | 0.015–0.025 | ≈0.035–0.05 at 400 °C; ≈0.05–0.09 at 500–600 °C | ≈650 °C continuous (unshielded); short exposures higher when faced | ≈70–300 kg/m³ | 1–5 mm (often 2–3 mm) | Compressible ≈10–30 %, partial rebound | Insulating; breakdown typically ≥3.5 kV per pad when encapsulated |
| Mica sheet / board (muscovite, phlogopite) | ≈0.2–0.6 (through-plane) | Stays ≈0.2–0.6 | Muscovite ≈500–600 °C; phlogopite ≈700–800 °C continuous; higher short-term | ≈1,800–2,350 kg/m³ (bonded sheet) | 0.2–2 mm | Essentially rigid | Excellent; typically ≥20 kV/mm at room temperature |
| Ceramic-fibre / bio-soluble fibre paper | ≈0.035–0.05 | ≈0.06–0.12 at 400 °C; ≈0.08–0.16 at 600 °C | Fibre rated ≈1,100–1,400 °C | ≈140–290 kg/m³ | 0.8–6 mm | Some initial compression; limited rebound | Good when dry; binder burns out at ≈250–450 °C |
| Intumescent / endothermic barrier sheet | ≈0.05–0.3 (before activation) | Not comparable: works by expanding or absorbing heat | Activates ≈150–200 °C; char stable to ≈1,000 °C | ≈300–1,500 kg/m³ | 0.5–3 mm between cells | Varies; expansion is irreversible | Depends on formulation: graphite-based chars become conductive |
| Silicone foam / compression pad | ≈0.06–0.15 | Polymer pyrolyses above ≈350 °C; ceramifying grades form a silica char | ≈200 °C continuous; fire-blocking grades survive short flame exposure | ≈190–800 kg/m³ | 1.5–6 mm | Best reversible compression and low compression set | Good |
| Phase-change material (PCM) plate | ≈0.2 (paraffin) to 3–15 (graphite composite) | Not applicable: decomposes above ≈200–300 °C | Melts at ≈25–70 °C; organic types unstable above ≈200 °C | ≈760–1,700 kg/m³ | 2–6 mm | Rigid | Paraffin insulates; graphite composites conduct |
| Composite barrier (aerogel or fibre core + mica / film facing) | ≈0.015–0.03 (aerogel core) | ≈0.04–0.06 at 500 °C (aerogel core); higher for fibre core | Facing survives short exposures ≈1,000 °C+ | ≈150–300 kg/m³ | 0.5–6 mm (often 1–3 mm) | Core compresses ≈10–30 % | Set by the mica or polymer facing |
Table 1. Typical ranges by class. Verified values for named products are listed in each section below.
1. Silica aerogel blanket / pad (fibre-reinforced)
Insulating core
Silica aerogel trapped in a glass- or ceramic-fibre mat. Its nanoporous structure suppresses gas conduction, giving the lowest thermal conductivity of the common barrier materials at room temperature and a clear advantage at a few hundred °C. Most battery grades are encapsulated in a film or faced with mica to control dust and add electrical and abrasion resistance.
- k at ~25 °C, W/(m·K)
- 0.015–0.025 Typical
- k at elevated temperature
- ≈0.035–0.05 at 400 °C; ≈0.05–0.09 at 500–600 °C Typical
- Temperature limit
- ≈650 °C continuous (unshielded); short exposures higher when faced Typical
- Density
- ≈70–300 kg/m³ Typical
- Typical thickness
- 1–5 mm (often 2–3 mm) Typical
- Compression
- Compressible ≈10–30 %, partial rebound Typical
- Electrical insulation
- Insulating; breakdown typically ≥3.5 kV per pad when encapsulated Typical
Strengths
- Lowest thermal conductivity of common barrier materials, so thin layers are effective
- Light and compressible, so it can double as a compression pad between prismatic or pouch cells
- Widely qualified in production EV packs
Limitations
- The silica network can sinter and lose its low conductivity above roughly 650–800 °C if not shielded
- Unencapsulated material sheds dust
- More expensive per square metre than mica or ceramic-fibre paper
Commercial examples
- PyroThin, Aspen Aerogels, USA
- Thermal Blade, JIOS Aerogel, Singapore / Korea
- Aerogel battery pads, IBIH Advanced Materials, China
- Aerogel battery insulation, Nano Tech Co. (纳诺科技), China
Listed for reference. Not an endorsement and not paid for.
2. Mica sheet / board (muscovite, phlogopite)
Flame & voltage shield
Mica paper bonded with silicone resin into flexible sheet or rigid board. It insulates heat about ten times worse than aerogel but is very hard to burn through, resists the abrasive jet of hot particles from a venting cell, and keeps high dielectric strength at temperature. It is the standard material for pack lids, busbar shields and the facing layer of composite barriers.
- k at ~25 °C, W/(m·K)
- ≈0.2–0.6 (through-plane) Typical
- k at elevated temperature
- Stays ≈0.2–0.6 Typical
- Temperature limit
- Muscovite ≈500–600 °C; phlogopite ≈700–800 °C continuous; higher short-term Typical
- Density
- ≈1,800–2,350 kg/m³ (bonded sheet) Typical
- Typical thickness
- 0.2–2 mm Typical
- Compression
- Essentially rigid Typical
- Electrical insulation
- Excellent; typically ≥20 kV/mm at room temperature Typical
Strengths
- Very high dielectric strength, retained at elevated temperature
- Resists flame burn-through and particle erosion
- Low cost and mature supply chain
Limitations
- High density and much higher thermal conductivity than aerogel
- Rigid: cannot absorb cell swelling on its own
Verified product values
| Product | Property | Value | Condition | Source |
|---|---|---|---|---|
| Pamitherm 41130 (phlogopite mica paper, silicone resin) Von Roll, via VRI Composites | k at ~25 °C, W/(m·K) | 0.18 W/(m·K) | temperature not stated | [2], properties table |
| Pamitherm 41130 (phlogopite mica paper, silicone resin) Von Roll, via VRI Composites | Temperature limit | 1000 °C | 'max. heat resistance' as stated by the supplier | [2], properties table |
Commercial examples
- Mica thermal runaway barriers, Elmelin, UK
- COGEMICANITE thermal runaway shields, Cogebi, Czech Republic
Listed for reference. Not an endorsement and not paid for.
3. Ceramic-fibre / bio-soluble fibre paper
High-temperature insulation
Paper made from alumina-silica refractory fibres or alkaline-earth silicate (bio-soluble) fibres with a small organic binder. It survives far higher temperatures than aerogel at low cost, but insulates less well at the temperatures that matter for propagation.
- k at ~25 °C, W/(m·K)
- ≈0.035–0.05 Typical
- k at elevated temperature
- ≈0.06–0.12 at 400 °C; ≈0.08–0.16 at 600 °C Typical
- Temperature limit
- Fibre rated ≈1,100–1,400 °C Typical
- Density
- ≈140–290 kg/m³ Typical
- Typical thickness
- 0.8–6 mm Typical
- Compression
- Some initial compression; limited rebound Typical
- Electrical insulation
- Good when dry; binder burns out at ≈250–450 °C Typical
Strengths
- Very high temperature resistance
- Low cost and light weight
- Easy to die-cut and laminate with mica
Limitations
- Higher conductivity than aerogel at 400–600 °C
- Organic binder burns off on first heating, releasing smoke
- Refractory ceramic fibre (RCF) has health classifications in some markets; bio-soluble grades avoid this
Verified product values
| Product | Property | Value | Condition | Source |
|---|---|---|---|---|
| 3M Thermal Runaway Barrier 600/700 3M | k at ~25 °C, W/(m·K) | < 0.045 W/(m·K) | 25 °C, mat only (non-classified inorganic fibre mat) | [3], Highlights |
| 3M Thermal Runaway Barrier 600/700 3M | Temperature limit | 1200 °C | base mat high-temperature stability | [3], Highlights |
| Superwool EST E Paper Morgan Advanced Materials | k at elevated temperature | 0.06 W/(m·K) | 200 °C; thickness-dependent where stated | [5], p. 2 |
| Superwool EST E Paper Morgan Advanced Materials | k at elevated temperature | 0.09 W/(m·K) | 400 °C; thickness-dependent where stated | [5], p. 2 |
| Superwool EST E Paper Morgan Advanced Materials | k at elevated temperature | 0.13 W/(m·K) | 600 °C; thickness-dependent where stated | [5], p. 2 |
| Superwool EST E Paper Morgan Advanced Materials | k at elevated temperature | 0.16 W/(m·K) | 800 °C; thickness-dependent where stated | [5], p. 2 |
| Superwool EST E Paper Morgan Advanced Materials | k at elevated temperature | 0.20 W/(m·K) | 1000 °C; thickness-dependent where stated | [5], p. 2 |
| Superwool EST E Paper Morgan Advanced Materials | Density | 450 kg/m³ | as supplied | [5], p. 2 |
| Superwool EST E Paper Morgan Advanced Materials | Typical thickness | 0.8–6 mm | available range | [5], p. 2 |
| Superwool EST E Paper Morgan Advanced Materials | Electrical insulation | >2 (dielectric breakdown; unit printed as 'kΩ, kV/mm') | as stated | [5], p. 2 |
| Superwool EST E Paper Morgan Advanced Materials | Temperature limit | 1100–1300 °C | classification temperature | [5], p. 2 |
| Superwool EST G Paper Morgan Advanced Materials | k at elevated temperature | 0.05 W/(m·K) | 200 °C; thickness-dependent where stated | [6], p. 2 |
| Superwool EST G Paper Morgan Advanced Materials | k at elevated temperature | 0.07 W/(m·K) | 400 °C; thickness-dependent where stated | [6], p. 2 |
| Superwool EST G Paper Morgan Advanced Materials | k at elevated temperature | 0.11 W/(m·K) | 600 °C; thickness-dependent where stated | [6], p. 2 |
| Superwool EST G Paper Morgan Advanced Materials | k at elevated temperature | 0.16 W/(m·K) | 800 °C; thickness-dependent where stated | [6], p. 2 |
| Superwool EST G Paper Morgan Advanced Materials | k at elevated temperature | 0.23 W/(m·K) | 1000 °C; thickness-dependent where stated | [6], p. 2 |
| Superwool EST G Paper Morgan Advanced Materials | Density | 240–300 kg/m³ | as supplied | [6], p. 2 |
| Superwool EST G Paper Morgan Advanced Materials | Typical thickness | 1–6 mm | available range | [6], p. 2 |
| Superwool EST G Paper Morgan Advanced Materials | Electrical insulation | >2 (dielectric breakdown; unit printed as 'kΩ, kV/mm') | as stated | [6], p. 2 |
| Superwool EST G Paper Morgan Advanced Materials | Temperature limit | 1100–1300 °C | classification temperature | [6], p. 2 |
| Superwool EST P Paper Morgan Advanced Materials | k at elevated temperature | 0.05 W/(m·K) | 200 °C; thickness-dependent where stated | [7], p. 2 |
| Superwool EST P Paper Morgan Advanced Materials | k at elevated temperature | 0.07 W/(m·K) | 400 °C; thickness-dependent where stated | [7], p. 2 |
| Superwool EST P Paper Morgan Advanced Materials | k at elevated temperature | 0.11 W/(m·K) | 600 °C; thickness-dependent where stated | [7], p. 2 |
| Superwool EST P Paper Morgan Advanced Materials | k at elevated temperature | 0.16 W/(m·K) | 800 °C; thickness-dependent where stated | [7], p. 2 |
| Superwool EST P Paper Morgan Advanced Materials | k at elevated temperature | 0.23 W/(m·K) | 1000 °C; thickness-dependent where stated | [7], p. 2 |
| Superwool EST P Paper Morgan Advanced Materials | Density | 272–352 kg/m³ | as supplied | [7], p. 2 |
| Superwool EST P Paper Morgan Advanced Materials | Typical thickness | 1–6 mm | available range | [7], p. 2 |
| Superwool EST P Paper Morgan Advanced Materials | Electrical insulation | >3 (dielectric breakdown; unit printed as 'kΩ, kV/mm') | as stated | [7], p. 2 |
| Superwool EST P Paper Morgan Advanced Materials | Temperature limit | 1100–1300 °C | classification temperature | [7], p. 2 |
| Superwool EST C30 compression paper Morgan Advanced Materials | k at elevated temperature | 0.06 W/(m·K) | 200 °C, ASTM C201 / ASTM C177 as printed in the table header; thickness-dependent where stated | [9], p. 2 |
| Superwool EST C30 compression paper Morgan Advanced Materials | k at elevated temperature | 0.08 W/(m·K) | 400 °C, ASTM C201 / ASTM C177 as printed in the table header; thickness-dependent where stated | [9], p. 2 |
| Superwool EST C30 compression paper Morgan Advanced Materials | k at elevated temperature | 0.11 W/(m·K) | 600 °C, ASTM C201 / ASTM C177 as printed in the table header; thickness-dependent where stated | [9], p. 2 |
| Superwool EST C30 compression paper Morgan Advanced Materials | k at elevated temperature | 0.15 W/(m·K) | 800 °C, ASTM C201 / ASTM C177 as printed in the table header; thickness-dependent where stated | [9], p. 2 |
| Superwool EST C30 compression paper Morgan Advanced Materials | Density | 240–310 kg/m³ | as supplied | [9], p. 2 |
| Superwool EST C30 compression paper Morgan Advanced Materials | Compression | 25–35 / 380–470 kPa | compression resistance at 20 % / 60 % deflection | [9], p. 2 |
| Superwool EST C310 compression paper Morgan Advanced Materials | k at elevated temperature | 0.06 W/(m·K) | 200 °C, ASTM C201 / ASTM C177 as printed in the table header; thickness-dependent where stated | [9], p. 2 |
| Superwool EST C310 compression paper Morgan Advanced Materials | k at elevated temperature | 0.08 W/(m·K) | 400 °C, ASTM C201 / ASTM C177 as printed in the table header; thickness-dependent where stated | [9], p. 2 |
| Superwool EST C310 compression paper Morgan Advanced Materials | k at elevated temperature | 0.10 W/(m·K) | 600 °C, ASTM C201 / ASTM C177 as printed in the table header; thickness-dependent where stated | [9], p. 2 |
| Superwool EST C310 compression paper Morgan Advanced Materials | k at elevated temperature | 0.13 W/(m·K) | 800 °C, ASTM C201 / ASTM C177 as printed in the table header; thickness-dependent where stated | [9], p. 2 |
| Superwool EST C310 compression paper Morgan Advanced Materials | Density | 400–510 kg/m³ | as supplied | [9], p. 2 |
| Superwool EST C310 compression paper Morgan Advanced Materials | Compression | 295–340 / 1700–1970 kPa | compression resistance at 20 % / 60 % deflection | [9], p. 2 |
Commercial examples
- FyreWrap LiB papers, Alkegen (formerly Unifrax), USA
- Thermal Runaway Barrier 600/700 Series, 3M, USA
- Superwool EST E, G, P and compression papers, Morgan Advanced Materials, UK
Listed for reference. Not an endorsement and not paid for.
4. Intumescent / endothermic barrier sheet
Active, expands in fire
Active materials. Intumescent sheets swell into an insulating char when heated, filling gaps and adding thickness. Endothermic sheets absorb heat by releasing chemically bound water. Both buy time rather than offering a fixed thermal resistance.
- k at ~25 °C, W/(m·K)
- ≈0.05–0.3 (before activation) Typical
- k at elevated temperature
- Not comparable: works by expanding or absorbing heat Typical
- Temperature limit
- Activates ≈150–200 °C; char stable to ≈1,000 °C Typical
- Density
- ≈300–1,500 kg/m³ Typical
- Typical thickness
- 0.5–3 mm between cells Typical
- Compression
- Varies; expansion is irreversible Typical
- Electrical insulation
- Depends on formulation: graphite-based chars become conductive Typical
Strengths
- Thin when cold; insulation increases in a fire
- Endothermic types delay temperature rise of the protected cell
- Expansion seals gaps against hot gas
Limitations
- Single use: the reaction is irreversible
- Expandable-graphite chars conduct electricity unless laminated with a dielectric
- Expansion force can load the neighbouring cells
5. Silicone foam / compression pad
Compression & sealing
Closed-cell or syntactic silicone foams used mainly to manage cell swelling and hold stack pressure. Fire-rated and ceramifying grades add some thermal-runaway protection, often in combination with a mica or aerogel layer.
- k at ~25 °C, W/(m·K)
- ≈0.06–0.15 Typical
- k at elevated temperature
- Polymer pyrolyses above ≈350 °C; ceramifying grades form a silica char Typical
- Temperature limit
- ≈200 °C continuous; fire-blocking grades survive short flame exposure Typical
- Density
- ≈190–800 kg/m³ Typical
- Typical thickness
- 1.5–6 mm Typical
- Compression
- Best reversible compression and low compression set Typical
- Electrical insulation
- Good Typical
Strengths
- Excellent long-term compression behaviour for cell breathing
- Seals and gaskets well
- UL 94 V-0 grades are common
Limitations
- Higher conductivity than aerogel
- Continuous service limited to about 200 °C
- Releases volatiles when it decomposes
Commercial examples
- ProCell EV firewall and BISCO silicones, Rogers Corporation, USA
- ELASTOSIL battery protection silicones, Wacker Chemie, Germany
Listed for reference. Not an endorsement and not paid for.
6. Phase-change material (PCM) plate
Thermal buffer (not a fire barrier)
Plates that absorb heat while melting, used to smooth temperature peaks in normal operation. They are not fire barriers: organic PCMs are flammable and graphite-filled composites conduct heat toward neighbouring cells once the latent heat is used up.
- k at ~25 °C, W/(m·K)
- ≈0.2 (paraffin) to 3–15 (graphite composite) Typical
- k at elevated temperature
- Not applicable: decomposes above ≈200–300 °C Typical
- Temperature limit
- Melts at ≈25–70 °C; organic types unstable above ≈200 °C Typical
- Density
- ≈760–1,700 kg/m³ Typical
- Typical thickness
- 2–6 mm Typical
- Compression
- Rigid Typical
- Electrical insulation
- Paraffin insulates; graphite composites conduct Typical
Strengths
- Large latent heat buffers short temperature spikes
- Can reduce cooling-system demand
Limitations
- No protection once melted
- Organic PCMs add fuel in a fire
- Graphite composites conduct heat and electricity
Verified product values
| Product | Property | Value | Condition | Source |
|---|---|---|---|---|
| Rubitherm RT35HC Rubitherm Technologies | k at ~25 °C, W/(m·K) | 0.2 W/(m·K) | both phases (solid and liquid) | [1], p. 1 |
| Rubitherm RT35HC Rubitherm Technologies | Density | 0.83 kg/L | solid, 20 °C (0.77 kg/L liquid, 40 °C) | [1], p. 1 |
| Rubitherm RT35HC Rubitherm Technologies | Temperature limit | 70 °C | max. operation temperature; melting range 34–36 °C; flash point 177 °C | [1], p. 1 |
Commercial examples
- RT35HC, Rubitherm Technologies, Germany
Listed for reference. Not an endorsement and not paid for.
7. Composite barrier (aerogel or fibre core + mica / film facing)
All-round production barrier
Laminates that put a low-conductivity core (aerogel or fibre) between tougher facings (mica, ceramic paper, polyimide or PET film). This is the dominant format in current production because it covers all four barrier jobs: insulation, compliance, dielectric strength and burn-through resistance.
- k at ~25 °C, W/(m·K)
- ≈0.015–0.03 (aerogel core) Typical
- k at elevated temperature
- ≈0.04–0.06 at 500 °C (aerogel core); higher for fibre core Typical
- Temperature limit
- Facing survives short exposures ≈1,000 °C+ Typical
- Density
- ≈150–300 kg/m³ Typical
- Typical thickness
- 0.5–6 mm (often 1–3 mm) Typical
- Compression
- Core compresses ≈10–30 % Typical
- Electrical insulation
- Set by the mica or polymer facing Typical
Strengths
- Balances insulation, compression, dielectric and burn-through performance
- Dust-free when fully encapsulated
Limitations
- Higher cost than single materials
- Thicker and heavier than bare aerogel
Verified product values
| Product | Property | Value | Condition | Source |
|---|---|---|---|---|
| Rogers ProCell TB1000 thermal insulation board Rogers Corporation | k at ~25 °C, W/(m·K) | 0.029 W/(m·K) | 25 °C, ISO 8301, typical | [4], p. 1 |
| Rogers ProCell TB1000 thermal insulation board Rogers Corporation | k at elevated temperature | 0.030 W/(m·K) | 200 °C, ISO 8301, typical | [4], p. 1 |
| Rogers ProCell TB1000 thermal insulation board Rogers Corporation | k at elevated temperature | 0.032 W/(m·K) | 400 °C, ISO 8301, typical | [4], p. 1 |
| Rogers ProCell TB1000 thermal insulation board Rogers Corporation | k at elevated temperature | 0.035 W/(m·K) | 600 °C, ISO 8301, typical | [4], p. 1 |
| Rogers ProCell TB1000 thermal insulation board Rogers Corporation | k at elevated temperature | 0.037 W/(m·K) | 800 °C, ISO 8301, typical | [4], p. 1 |
| Rogers ProCell TB1000 thermal insulation board Rogers Corporation | Density | 350–450 kg/m³ | as supplied | [4], p. 1 |
| Rogers ProCell TB1000 thermal insulation board Rogers Corporation | Typical thickness | 0.8–5.0 mm | available range (tolerance ±0.15–0.2 mm) | [4], p. 1 |
| Superwool EST M Paper (mica-laminated) Morgan Advanced Materials | k at elevated temperature | 0.04 W/(m·K) | 200 °C, descending, thickness-dependent; thickness-dependent where stated | [8], p. 2 |
| Superwool EST M Paper (mica-laminated) Morgan Advanced Materials | k at elevated temperature | 0.06 W/(m·K) | 400 °C, descending, thickness-dependent; thickness-dependent where stated | [8], p. 2 |
| Superwool EST M Paper (mica-laminated) Morgan Advanced Materials | k at elevated temperature | 0.08–0.09 W/(m·K) | 600 °C, descending, thickness-dependent; thickness-dependent where stated | [8], p. 2 |
| Superwool EST M Paper (mica-laminated) Morgan Advanced Materials | Electrical insulation | > 2 kV | withstand voltage, 2 minutes | [8], p. 2 |
| Superwool EST M Paper (mica-laminated) Morgan Advanced Materials | Typical thickness | 1–6 mm | available range | [8], p. 2 |
| Superwool EST M Paper (mica-laminated) Morgan Advanced Materials | k at elevated temperature | < 230 / < 200 / < 140 °C (cold face) | 600 °C hot face, 20 min; 1 / 3 / 6 mm thickness | [8], p. 2 |
Commercial examples
- AlkeGel aerogel composites, Alkegen, USA
- ProCell TB1000, Rogers Corporation, USA (composition not stated in datasheet)
- Superwool EST M Paper, Morgan Advanced Materials, UK
Listed for reference. Not an endorsement and not paid for.
Choosing a material for a specific cell or part?
Tell us the cell format, thickness, size and test standard, and we reply with sourced options. Submit a requirement
Sources
- Rubitherm Technologies GmbH. RT35HC data sheet. Datasheet, accessed 2026-11-15. Archived copy.SHA-256 d028ca73db2a3f534ea05aab8274b6b56de0cc800b7a48ce4be63fa2d00724fe
- VRI Composites (distributor, Augsburg, Germany). PAMITHERM 41130 product page. Datasheet, accessed 2026-11-15.
- 3M. 3M Thermal Runaway Barrier 600/700 Series, product page. manufacturer page, accessed 2026-11-15.
- Rogers Corporation. ProCell TB1000 Thermal Insulation Board, product data sheet (publication 180-506). Datasheet, accessed 2026-11-15. Archived copy.SHA-256 2a72add859e4d836100d47ae18e04c7164cb4c5e00c7ecb87cf302ea61dea302
- Morgan Advanced Materials (Thermal Ceramics). EST E Paper, product data sheet (publication date 1 January 2025). Datasheet, accessed 2026-11-15. Archived copy.SHA-256 5afe8b942e72a8a65ca97155826b451769acd207bf2793aec76897a11a2ea3ab
- Morgan Advanced Materials (Thermal Ceramics). EST G Paper, product data sheet (publication date 1 January 2025). Datasheet, accessed 2026-11-15. Archived copy.SHA-256 4ab3bd2d2e12a138e5b9c689c3ed28a6facdb7365128253cb58451404fed7c1e
- Morgan Advanced Materials (Thermal Ceramics). EST P Paper, product data sheet (publication date 1 January 2025). Datasheet, accessed 2026-11-15. Archived copy.SHA-256 425a76a78ea166b82388fe540bec65b014295d1ee1d5f86ea324076f1d00eb30
- Morgan Advanced Materials (Thermal Ceramics). EST M Paper, product data sheet (publication date 1 January 2025). Datasheet, accessed 2026-11-15.SHA-256 3dbf4ec8620abe09937ce8cf89275ea9e0848a440437bc5f28132b15b16d920d
- Morgan Advanced Materials (Thermal Ceramics). EST Compression Papers (C30, C310), product data sheet (publication date 1 January 2025). Datasheet, accessed 2026-11-15.SHA-256 e10ce721f30b0a050808999bd8242a6a146b06a98da07e9157853fb21de4f95c